How mold remediation works, step by step
Every company has its own process, but good remediation follows the same logic. Here is what to expect and what to ask.
Call (855) 671-5199The usual steps
- Assess. Find where mold is, how far it spread and where the moisture comes from, often with a moisture meter.
- Fix the moisture. A leak, a drain line, a roof or a crawl space problem has to be repaired. The EPA says the key to mold control is moisture control.
- Contain. For larger jobs, the work area is sealed off so spores do not spread through the house.
- Remove. Materials that cannot be cleaned, such as soaked drywall or insulation, are removed and bagged. The EPA notes that dead mold can still cause allergic reactions, so mold must be physically removed.
- Clean. Remaining surfaces are cleaned, often with HEPA vacuuming and damp wiping.
- Dry. Fans and dehumidifiers dry the area.
- Check. Moisture readings and a visual check confirm the area is dry and clean. The EPA notes surface sampling may help confirm cleaning, if done by an experienced professional.
- Rebuild. Replace what was removed. This is often a separate job.
Equipment and methods you may see
The EPA's remediation guide was written for schools and commercial buildings, and the EPA notes that its methods apply to other building types too (EPA remediation guide). It describes these methods:
| Method or equipment | What the EPA says |
|---|---|
| Moisture meter | Measures moisture in building materials after water damage and tracks drying. A humidity gauge monitors indoor humidity. |
| Damp wiping or scrubbing | Mold can generally be removed from hard, nonporous surfaces by wiping or scrubbing with water, then drying quickly. |
| Removal of porous materials | Moldy porous materials such as gypsum board may need to be discarded. Unsalvageable material is sealed before leaving the work area, double-bagged in 6-mil polyethylene. |
| Wet vacuum | For water removal only, while materials are still wet. Not for porous materials such as drywall. |
| HEPA vacuum | Recommended for final cleanup after materials are thoroughly dry. Filters and contents are sealed in plastic bags. |
| Containment | Limited containment for roughly 10 to 100 square feet uses a single layer of 6-mil polyethylene. Larger areas, or occupied space at risk, call for full containment with double layers and an airlock. |
| Negative pressure | The containment area is kept under negative pressure relative to surrounding areas, for example with a HEPA-filtered fan vented outside. Sheeting that billows inward shows it is working. |
| HVAC filters | The EPA suggests upgrading to at least MERV 8 and changing filters after remediation. Ordinary filters are typically not effective for particles the size of mold spores. |
Larger jobs may also use air scrubbers and dehumidifiers to dry the space. Ask what equipment the company will use and why. The EPA says bleach or another biocide is not recommended as a routine practice, because the goal is to remove mold, not just kill it.
What to ask before work begins
- What is the written scope, and what is not included?
- What caused the moisture, and how will it be fixed?
- How will you contain the area?
- How will we know the job is done?
- Who handles the rebuild?
What to do while you wait
- Stay out of the work area, and keep children, pets and anyone with asthma or a weakened immune system away.
- Keep the HVAC off in the affected area if the company advises it.
- Photograph the area before work begins and keep the estimate and invoice.
Sources: EPA guide to mold and moisture. Specific steps vary by company and by job.
Common questions
What are the main steps?
Typically: find and fix the moisture, set up containment where needed, remove materials that cannot be cleaned, clean the rest, dry everything and check that the area is dry. Steps vary by company and job.
How will I know the job is done?
Ask for a written scope up front and for moisture readings or a final check at the end. The EPA notes that surface sampling may help confirm an area was cleaned, if done by an experienced professional.
Can I stay in the house during remediation?
It depends on the size and location. Ask the company. People with asthma or weakened immune systems should stay away from the work area.
Who rebuilds afterward?
Often a separate contractor, although some companies offer both. Ask who is responsible for replacing drywall, insulation and flooring.
Found mold or a leak? Call and we will connect you with an independent local mold remediation or restoration company, day or night, subject to availability.
Call (855) 671-5199Calling is free. Ask the company for an estimate before work begins.